Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision 		Previous revision
room_sixteen [2017/03/19 20:25]
John Benedetto created 		room_sixteen [2023/03/27 14:33] (current)
John Benedetto
Line 1: Line 1:
-====== Electronics Lab ======+====== 3D Printing Room ======
  
-<WRAP third right box>**Area Captain** \\ +<WRAP box>**Area Captain** \\ 
-Aaron Birenboim\\ +Tim Torres\\ 
-//ee.net//+3dprinting@quelab.net
  
-</WRAP>+<wrap caution>YELLOW TOOLS</wrap>\\ 
 +Creality CR-10 Mini\\ 
 +Orion Delta Printer\\ 
 +Prusa i3</WRAP>
  
-The Electronics lab contains tools & equipment to work on your electronics projects.  Please keep your bench area clean & return tools when you are finished with them.  If you are leaving a project in the area, please tag it with a green PERSONAL PROJECT tag, so we know whose it is.+<WRAP round caution>The 3D Printers are [[:training|YELLOW tools]], and require additional training</WRAP> 
 + 
 +To help make 3D printing at quelab awesome-er, sign up for the [[http://pepper.quelab.net/mailman/listinfo/3d-printing|3d-printing mailing list]]. It's low-volume, but high-quality. 
 + 
 +===== Makes and models ===== 
 + 
 +  * [[:prusa_mendel|Prusa Mendel]] 
 +  * [[:prusai3|Prusa ]] 
 +  * [[:blinky|]] - troybot 
 +  * [[:orion|SeeMeCNC ORION Delta Printer]] 
 +  * [[:makerbot|Makerbot Cupcake / Thing-o-Matic - Thing1 & Thing2]] 
 + 
 +===== Training & Problems ===== 
 + 
 +<WRAP important round> Training is currently in flux. To be trained on the 3D printers, please contact the 3D printing officer via the [[http://pepper.quelab.net/mailman/listinfo/3d-printing|3d-printing mailing list]] to set up meeting on an open night. Without prior arrangement, there is no guarantee that there will be a 3D printing trainer available during an open night, however. </WRAP> 
 + 
 +For information on usage, tips and 3D printing stuff, see: 
 + 
 +  * Using [[:3dprinter_usage|MatterControl]] to print models, as well as 
 +  * A set of [[:hardware:3dprinter:care_and_feeding|troubleshooting and maintenance]] steps. 
 + 
 +===== Materials ===== 
 + 
 +The table below specifies costs of materials kept at Quelab. 
 + 
 +<WRAP info> All values are in //per-gram//  increments of ALL consumed materials, **including**  failed prints and support material.</WRAP> 
 + 
 +^Material^Members^Non-Members| 
 +|ABS|$0.10|$0.20| 
 +|PLA|$0.10|$0.20| 
 +|NinjaFlex(([[:prusai3|Prusa i3]] only))    |TBD: Likely in the $0.60/g range|| 
 +|IGUS [[http://www.igus.com/wpck/15422/iglidur_TriboFilament|Tribo]]|Go get a sample from IGUS. It's expensive.|| 
 + 
 +Materials must be cleared by a 3D printing officer. 
 + 
 +Materials previously cleared for use in the 3D printers: 
 + 
 +  * Filamentium / FilamentOne PLA Extrafill 
 +  * Zen Toolworks ABS and PLA 
 +  * NinjaFlex 
 +  * IGUS Tribo filament 
 +  * Push Plastic ABS and PLA 
 +  * Taulman Nylon 230 
 + 
 + 
 +[[room_map | Return to the building map]]
  
-[[room_map|Return to building map]]