Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
3dprinter_usage [2016/05/31 23:45]
morgang 		3dprinter_usage [2023/03/27 14:29] (current)
John Benedetto
Line 6: Line 6:
  
 **THIS CONTENT IS IN BETA ** </WRAP> **THIS CONTENT IS IN BETA ** </WRAP>
 +
 +
 ===== The MatterControl interface ===== ===== The MatterControl interface =====
  
Line 16: Line 18:
 ==== Printer Status ==== ==== Printer Status ====
  
-{{:hardware:3dprinter:usage_mattercontrol_view_status.png?200  }}Printer Status | shows the status of the current printer, as well as allowing you to disconnect or connect to a different printer.+{{:hardware:3dprinter:usage_mattercontrol_view_status.png?200  }} shows the status of the current printer, as well as allowing you to disconnect or connect to a different printer. When connected, this view allows you to preheat the printer, according to the settings that are currently configured. 
 + 
 +==== Printer Status (while printing) ==== 
 + 
 +{{:hardware:3dprinter:usage_mattercontrol_status_printing.png?200 |Printer Status (printing)}} While printing, the current print is shown, including estimated print time, current duration of print, progress in percentage, hotend and bed temperatures, plus buttons to temporarily pause the print or end the print entirely. 
 + 
 +**n.b.** when canceling a print, the hotend and bed will be turned off, allowing them to cool; if you wish to resume printing quickly, be sure to press the "preheat" options quickly, as the time to heat the bed is much greater than to cool it! 
  
 ==== Queue ==== ==== Queue ====
Line 33: Line 41:
     * Fill Density: The amount of material that the 3D printed object will actually be solid within the interior. Common values for this are: 1-20% (0.1 0.2) for decorative pieces, 50% (0.5) for light     * Fill Density: The amount of material that the 3D printed object will actually be solid within the interior. Common values for this are: 1-20% (0.1 0.2) for decorative pieces, 50% (0.5) for light
  
-==== MatterControl: Printer control ====+==== Printer control ====
  
 {{:hardware:3dprinter:usage_mattercontrol_contro.png?200  }} {{:hardware:3dprinter:usage_mattercontrol_contro.png?200  }}
Line 44: Line 52:
  
     - Turn on the printer. For each printer, there is a switch which controls mains power.     - Turn on the printer. For each printer, there is a switch which controls mains power.
-    - Check the preflight list for [[:hardware:3dprinter:start#makes_and_models|the printer you wish to use]].+    - Check the preflight list for [[:room_sixteen#makes_and_models|the printer you wish to use]].
     - Open MatterControl and connect to the printer you wish to use.     - Open MatterControl and connect to the printer you wish to use.
     - Add the model you wish to print to the MatterControl queue     - Add the model you wish to print to the MatterControl queue
     - Check settings for the model you wish to print, e.g. layer height (resolution) and infill density.     - Check settings for the model you wish to print, e.g. layer height (resolution) and infill density.
     - Press print. MatterControl should take it from there.     - Press print. MatterControl should take it from there.
- 
-===== Pausing/stopping a print ===== 
- 
-Use the Printer Status buttons to pause or stop a print while the printer is running. If you wish to immediately start printing again, be sure to preheat the printer using the temperature buttons in the Printer Status view. 
  
 ====== Removing prints from the bed ====== ====== Removing prints from the bed ======